Kryptaglow® MEA Special Blend 1300, 1300A & 1300C  (Water Base)

Product Data Sheet

 

 

 

 

Product Description

 

 

Kryptaglow® MEA Special Blend 1300, 1300A & 1300C Water Based Paint.  Product must be applied over a white base coat.

 

 

Physical Properties

 

Resin Type

Reduction Solvent

Clean-up Solvent

Solids by Weight

Solids by Volume

 

Recommended Dry Film

Thickness per Coat

 

Theoretical Coverage @ 1 mil

 

Practical Coverage at

Recommended DFT1

 

Dry Times2

@ 70 º F (21 º C)

and 50% R.H.

Recoat 1 to 2 hours3

 

VOC’s

 

Acrylic

Water

Water

33%

31%

 

1 – 2 mils

 

 

497 ft2/gallon

 

248 – 489 ft2/gallon

 

 

Touch 10 minutes

Tack Free 1 hour

Through 2 to 4 hours

Recoat after Tack Free

 

280 grams/liter

 

1 Spread rates are estimates based on products volume solids and make no allowance for material loss during application.  Actual spread rates may vary dependent on applicator experience, surface porosity and texture.

2 Dry times may vary depending upon temperature, humidity and degree of air movement.

3  For the best results when using as a stain blocker, allow 24 hours between coats: two (2) full coats may be required for optimum performance.

 


 

Surface Preparation

 

 

                 

 

                  Masonry Surfaces:

                       Poured Concrete

                       Concrete Block

 

                  Wood Surfaces

 

                 

                  Plaster Surfaces:

 

                 

                 

 

                 

                  Drywall Surfaces

 

 

 

                 

                  New Galvanized

                  Aluminum Metal Surfaces:

 

                  Weathered Galvanized

                  Aluminum Surfaces:

 

                  Ferrous Metal Surfaces:

 

                  Previously Painted                   Surfaces:

 

 

 

 

 

 

                  Mildew:

 

All surfaces must be cured, clean, sound, dry and free of all dirt, dust, efflorescence, wax, oil, grease, chalk and any other contamination that would interfere with new coating adhesion. Bare surfaces must be properly prepared and primed prior to application of this product. Product must be applied over a white base coat.

 

New concrete and mortar should cure for a minimum of 30 days at 72° F (22° C) prior to coating application. Level all surface projections and mortar spatters by stoning. Rake mortar joints clean and remove all soluble salts.

 

Sand smooth any exposed wood surfaces. Patch nail holes and any imperfections with wood filler or putty and sand smooth. Remove sanding dust.

 

New plaster must cure for a minimum of 30 days at 72° F (22° C) prior to coating application. Sand smooth and dust. Fill cracks with spackling compound, allow to dry and sand smooth. Remove sanding dust.

 

 

Fill nail holes and imperfections with spackling compound and allow to dry. Sand tape joints and spackled areas and remove dust. New drywall should be primed with an appropriate PVA primer or used as self-priming.

 

 

Solvent wipe to remove surface contamination, then use an etching solution or abrade the surface by sanding.

 

Power or hand wash with detergent and rinse thoroughly. The surface must be dull and slightly rough; use an etching solution or sand if needed.

 

Remove loose rust and mill scale with hand or power abrading tools (reference SSPC-SP-2 or SSPC-SP-3).

 

1) Cleaning is recommended to remove contamination. If oil or grease is present, use of a cleaner/degreaser is required. All cleaning residue must be completely rinsed from the surface. Allow to dry.

2) Remove all loose coatings and corrosion by scraping, sanding or other abrading method. Dull glossy, slick and/or non-porous surfaces with sandpaper

3) Patch and fill areas as needed. Spot primer bare areas with appropriate primer.

 

Remove by using a solution of one (1) part household bleach and three (3) parts water. Apply to mildewed area and scrub. Allow solution to remain on the surface for 3 to 5 minutes then rinse completely and allow to dry before coating application. Do not add detergents or ammonia to the bleach/water solution.

 

 

Application

 

 

Stir material vigorously prior to application.

 

Apply by brush or roller. A good quality synthetic brush will make application easier. Select a roller cover suited for the texture of the surface to be coated.

 

Apply the product in full even coats and maintain a wet edge. Allow the product to dry between coats.

 

Do not thin.

 

 

Environmental variables

 

 

Protect product from freezing prior to and during application. Minimum surface and air temperature required for application is 50° F (10° C) and at least 5° F (3° C) above the dew point. Curing is affected by temperature, humidity and air movement. The minimums must be maintained for at least eight (8) hours in order to achieve proper film formation. Application at elevated temperatures, wind conditions, and/or low humidity may require special application procedures to achieve proper film formation.

 

 

Clean-up

 

 

Clean up spills immediately with soap and warm water. Clean hands and tools immediately after use with soap and warm water.

 

Coating must be fully cured before attempting to wash the surface. Curing is temperature and humidity sensitive, ranging from 14 to 28 days.

 

 

Safety Precautions

 

 

 

Do not apply below 50° F.

Protect from freezing

Do not take internally

Use with adequate ventilation

Keep out of reach of children

 

For more detailed recommendations, please contact your local Kryptaglow Representative

 

 

 

 

 

 

Co-Leash, Inc.

P.O. Box 272672

Tampa, FL 33688

(P) 813/920-1910        (F) 813/792-1418

www.kryptaglow.com